How to Install a Ghost Immobiliser
A ghost immobiliser guards your vehicle from key cloning and hacking. It works by stopping the vehicle's engine from starting until it is started with the PIN code that can be as long as 20 characters.
This extra layer of protection isn't visible to thieves who might not be aware of it. Some systems also have an app that allows owners to disable the immobiliser in the event that they forget their PIN code, or to use a service/valet mode.
Connecting the vehicle's CAN Bus to the vehicle's
The Ghost 2 Immobiliser is a cutting-edge security system, can be integrated directly into the ECU of your vehicle. It offers a discrete security barrier against thieves. It is highly efficient and user-friendly, making it a valuable option to add to your vehicle's security arsenal. Like all anti-theft devices it's not foolproof and requires regular maintenance to function effectively. Luckily, this guide will assist you in getting the most benefit from your Ghost 2 Immobiliser.
CAN (Controller Area Network) is a reliable serial network that lets microcontrollers communicate with each other over short distances without the necessity of central control units. It is designed to allow multiplexing of electrical wiring in vehicles to reduce copper usage and has a number of advantages, such as low cost and a simple use.
In modern vehicles In modern cars, the CAN protocol is used to connect with a variety of systems, including the engine management system (EMS) steering module, transmission controller, air conditioning controls and more. It also carries sensor data, such as speed sensors and inputs to control different features of the car. The CAN bus is used to monitor these various components, and it can stop the car from starting if they're in a dangerous state.
It's crucial to understand how the CAN bus functions and how it's secured. Using CAN bus could be an excellent method to add new features to your vehicle, but it's vital to protect it from threats such as hackers and other. Installing a firewall and monitoring your CAN-bus with software is the best way to achieve this.
Ghost2's discreet control unit is concealed in the wiring harness or dashboard, removing the possibility of a thief physically tampering with it. It is also impossible to reset the PIN or emergency code without access to the vehicle.
If you must give your car away for maintenance, valet parking, or any other reason, you can turn on the Transport Mode. This feature disables the Ghost immobiliser's ignition and keyfob functions, and will only be activated when the vehicle is speeding at 31 mph for 15 minutes.
The process of creating a PIN code
The Ghost immobiliser protects your car from theft. The most advanced technology utilizes the PIN code to shut down the engine and stop it from starting if you do not have the correct code or a valid fob or mobile device. The system's sleek design makes it unnoticeable, and offers unrivaled security against theft. Furthermore the system is TASSA verified and can lead to significant savings on insurance premiums for cars.
During installation, Ghost enters a "learning mode" to record the sequence of buttons pressed in order to create your unique pin codes. Once the pin code is created the installer will guide you through the steps to activate the system. Once activated the Ghost system will disable your vehicle's starting motor unless you enter a valid pin or switch the vehicle into transport mode. This makes it very difficult for thieves or cloners to hack into or clone your vehicle's starter system.
It is easy to install it is easy to install a Ghost immobiliser, however, you must follow the detailed instructions provided in the user's guide to ensure the proper operation. Multimeters and hand tools can be used to verify electrical values. Insulation tape and heat shrink tubing can shield the wire from damage, while cable tie is essential to keep everything tidy and secure. Test the system on a regularly to spot any potential issues.
It is crucial to test the system one last time before turning on the ignition. Ghost immobilisers will arm themselves after 3 to 30 second, depending on the model of the vehicle. It also has an option for Service/Valet that allows you to temporarily remove the system for servicing your vehicle or valet parking.
Idealy, the immobiliser will be hidden under the dashboard or the steering wheel. Use a small piece duct tape or paint over the wires CAN H and L to make them easier to locate during testing. Additionally, the CAN H and CAN L wires must be connected to a power source that is able to provide constant 12V. It is essential to test the connections again after testing as the incorrect identification of these wires could cause the system to malfunction.
Activating the system
A ghost immobiliser stops the car from starting unless you press a number of buttons in the vehicle, typically on the steering wheel, the door panel or the central console. The sequence is determined by the user and can be altered as needed. Once activated, the system cannot be turned off. This makes it an ideal choice for those who want to safeguard their vehicle against theft.
The system is designed not to be detectable by modern diagnostic and code-grabbing technologies. It also does not send out radio frequencies which makes it difficult for thieves to identify the device.
If the device is identified, it will stop the engine from starting and will sound an alarm that is loud enough to scare away the thief. The device can be used to track the location of a vehicle which can aid in the search for the vehicle in the event that it was stolen.
Contact Car Specalist Customs for a quote or to discuss your options if you're interested in an immobiliser that is ghost-like. We are fully trained to install a ghost immobiliser to your vehicle and will ensure it is concealed in a remote area. We can also install additional security measures, such as a kill switch or wheel lock to keep your vehicle safe from theft.
Disarming the system
It is important to know how to deactivate a Ghost immobiliser if installed in your vehicle. This is useful in the event that you lose your keys or the battery in your car dies. The system uses an individual PIN code that only you know, and the immobiliser will not start your vehicle unless you enter this code. The simplest method to enter the code is to press a series of buttons on your dashboard or the steering wheel. This is much easier than using a key fob, and keeps others from copying the remote.
Unlike some aftermarket immobilisers that require cutting wires for installation, Ghost2 is non-invasive and integrates with your vehicle's CAN bus network to function. Ghost 2 immobiliser is its ability bypass the engine without affecting your vehicle's normal functions, making it impossible for thieves to use signal boosters or clone your car key. Additionally, it doesn't emit radio frequencies, meaning thieves can't detect the system.
The Ghost system comes with the option of a Transport Mode which allows you to temporarily disable security for situations such as transportation or service. This is an excellent option if you have to lend your vehicle to someone without sharing the PIN code or in case you wish to secure your vehicle while driving it. To activate Transport Mode simply press the service button 5 times in a matter of 2 seconds. The Ghost system will confirm activation with 5 signal indicators.
When you're done, remember to save the emergency code in a safe place outside of your vehicle. If you ever find yourself locked out of your car You can call the company or technician who installed the system, and they will give you the code. If you are unable to reach them, you can always try to contact an authorized dealer however this will require verification procedures and could incur additional charges.
This system isn't just practical, but it can also safeguard your vehicle from theft, and also reduce the cost of insurance. Many insurance companies offer reduced monthly rates or even financial incentives for installing this anti-theft technology.